Go back one pageGo to the next page#Go to this book's Table of ContentsGo to this book's Index#


Configurator Procedure for Setting the Ingress Table

To set the ingress table for a voice module, use the Configurator procedures below:

  1. Select Configure, Voice, and Channels from the navigation window.
  2. You will see the Voice Channels window:

  3. At the top of the window, click on Ingress (Outgoing) Profiles. You will see the Voice Ingress (Outgoing) Profiles window:
  4. Click on Modify for the profile you wish to change. The Modifying a Voice Ingress (Outgoing) Profile window opens:

The optional parameters for the Voice Ingress (Outgoing) Profiles are described below:

Parameter

Range of Values

Required Action

Index

Passport 4430/50/55
INTEGER (1..32)

 

Passport 4460
INTEGER (1..60)

The lower the index number the higher the priority of the corresponding ingress number.

Phone Number/Pattern

"String" (0..40)

Enter a mix of alphanumeric characters (maximum 40). These are the characters the user must dial to reach the destination voice channel. The alpha characters are limited to the symbols *, [...], #, and +, with the meanings listed in the table below.

Manipulation String

"String" (0..40)

Enter a mix of alphanumeric characters (maximum 40). The alpha characters are limited to the symbols *, #, D, and I, with the meanings listed in the table below:

Voice Transport Method

  • Voice Over Frame Relay
  • Voice Over IP
  • As System

Select the manner in which voice traffic will be transported for this profile. As System will select the system transport method as configured in Configurator Procedure for Setting the System Transport Method.


Phone Number/Pattern Characters

*

Used as a single wildcard digit.

[xyz...]

Used as an exclusive single wild card. Any one digit within the brackets will produce a match; any other digit will be rejected.

Example 1: [234578]# will reject any string that begins with 0, 1, 6, or 9.

Example 2: 123[576]*# will match any phone number listed below:

1235*#, 1237*#, 1236*#

But will reject 1231*#, 1232*#, 1234*#, 1238*#, 129*#, and 1230*#.

#

Length of the dialing string is unknown. The voice application will continue collecting digits until one of three events occurs:

  • maximum number of digits reached
  • interdigit timeout occurred
  • user manually entered a # sign on the telephone keypad (if parameter is provisioned in the voice profile).

Digits preceding the # sign are immediately submitted for network address resolution. Digits following the # sign will be used to complete the call.

Example: Ingress table entry = 123#. User dials 123456. The digits 123 will be submitted immediately to resolve the network address, while the voice application collects digits 456. After one of the three events indicated above occurred, the digits 456 will be used to complete the call.

+

Used to obtain a second dial tone


Manipulation String Characters

*

Used as a single wildcard digit.

#

Used to wildcard the rest of the digits in the string immediately
following the #.

Dn

Deletes a particular number (n) of digits immediately following these characters, where (n) is a single digit ranging between 1 and 9. To delete more than 9 characters, you must enter additional deletions. For example, to delete 14 characters, insert the symbols D9D5.

D#

Deletes all of the digits immediately following these characters.

Innn

Inserts specified digits (nnn). Can be any number of digits.


  1. Click on the Save button when all desired parameters have been entered.
  2. Click on the Next and Previous buttons to configure other profiles in the ingress table. Typical ingress table settings are shown below:
  3. Index

    Ingress Number

    Manipulation String

    Number Transmitted

    1

    1234567

    D3****

    4567

    2

    12345678

    D3#

    45678

    3

    25

    I1234567

    251234567

    4

    1234567

    ***D2#

    12367

    5

    1234567

    D1**I9#

    2394567

    6

    123456789

    D2**I26#

    342656789


End of Topic


Nortel Networks LogoContact us by email
Go back one pageGo to the next page#Go to this book's Table of ContentsGo to this book's Index